UEXT From Wikipedia

UEXT From Wikipedia, the free encyclopedia

http://en.wikipedia.org/wiki/UEXT

Universal EXTension (UEXT) is a connector layout which includes power and three serials buses: Asynchronous, I2C, SPI. The connector layout was specified by Olimex Ltd and declared an open-project that is royalty-free.

Physical characteristics[edit source]

The UEXT connector consisting of 10 pins, in a two row by five male pin configuration, with a plastic keyed-shroud. All pins have a spacing of 0.1 inch (2.54 mm).[1][2] The socket is mated with a 2x5 (10-pin) IDC female connector, and typically connected to a Ribbon cable. The UEXT cable assembly is referred to as a 10-pin IDC Connector Ribbon Cable. These cables are readily available and cheap.[3]

Electrical characteristics

UEXT pinout for IDC connector

(looking into connector on host board)

The UEXT connector presents power and three serial buses: Asynchronous, I2C, SPI. All pins conform to 3.3 volt digital logic. The asynchronous serial bus requires additional level-shifting circuits and connectors to support RS-232, RS-422, RS-485, DMX512, MIDI.

UEXT Connector

Pin Name I/O Logic Primary Use

1 3.3V S S +3.3 volt

2 GND S S Ground

3 TXD O PP Transmit Data for Async Serial bus

4 RXD I PP Receive Data for Async Serial bus

5 SCL O OD Clock for I2C bus

6 SDA I/O OD Bidirectional Serial Data for I2C bus

7 MISO I PP Serial Data In for SPI bus

8 MOSI O PP Serial Data Out for SPI bus

9 SCK O PP Clock for SPI bus

10 SSEL O PP Slave Select for SPI bus

Notes:

Direction is relative to host board.[1] I = Input, O = Output.

S = Power Supply, PP = Push-Pull logic, OD = Open-Drain logic, all pins conform to 3.3 volt digital logic

Alternate pin uses

The functionality of most microcontroller pins are multipurpose thus allowing the engineer to redefine the purpose of the pin. It is fairly common that a pin will have a choice to be either a general purpose I/O or a peripheral.

If a microcontroller pin is connected to the UEXT connector and redefined to be something other than Asynchronous Serial Bus / I2C Bus / SPI Bus, then some design considerations should be considered before making the changes. To minimize the chance of damaging various UEXT boards or the microcontroller, redefined pins should continue to adhere to the direction of the data in this table or alternately redefined as an input. For a safe design, it is recommended that you don't redefine pins 4 or 7 to be outputs, and use pin 6 as an output with caution.

If a person is concerned about damaging the data lines of the microcontroller, additional over-voltage protection diodes and/or separate drivers should be added between the microcontroller and UEXT connector. Additionally, a resettable fuse might be added between the host power and pin 1 to protect against over-current conditions.

Similar connectors

Some devices use a layout based on the UEXT connector but have chosen not implement all of the functionality. In particular the asynchronous serial connection may have been omitted. In these cases the spare pins are usually assigned other purposes, such as connecting to a device reset line, so care should be taken to check the exact connector layout on the schematic of a particular device.




UEXT Universal EXTension connector

https://www.olimex.com/Products/Modules/UEXT/resources/UEXT_rev_B.pdf

UEXT is a board to board connector which supports three serial communication interfaces - I2C, SPI and RS232. It is a great way to expand the features of the development boards you already have. The customer can choose which new feature he wants to expand.

DOCUMENTS

UEXT guide revision B

UEXT Module Categories

Interface

Adapters

Sensors

LCD

LED

IO

Video

RF

RFID

Ethernet

Time

GPS

MP3

Biofeedback

.END